+27 (0)11 022 5323 +27 (0)72 435 0005
R
- -
Funnel Filter:
Connection Interface
General What's This?
IDC10 What's This?
mikroBUS What's This?
MagnifierSearch:
Storage (Go to Parent Category)
Boards implementing memory ICs / interfaces, such as RAM / Flash / EEPROM / SD Card.

(i) Tip:The filter on the left can be used to narrow down the number of items in this category.
  • Items
-
microSD click
 
mikroBUS
microSD click microSD Click is an accessory board, in mikroBus form factor, which features a microSD card connector. MicroSD cards are used as mass storage media for portable devices. They feature the industry standard SPI interface, which ensures simple communication at high data rates. The board is designed to use a 3.3V power supply only.
R230  Qty:
Weight: 20g. Stock: 2 available immediately [i]. mikroE Icon
-
MMC/SD
 
IDC10
MMC/SD The MMC/SD Board is an effective and low-cost board used to connect a development system to MMC or SD cards. This board uses SPI communication for data write or read to/from MMC/SD card. It comes with many ready-to-use examples.
R285  Qty:
Weight: 20g. Stock: 1 available immediately [i]. mikroE Icon
-
Flash click
 
mikroBUS
Flash click The Flash Click board is an accessory board in mikroBUS form factor. It's a compact and easy solution for adding flash memory to your device. It features M25P80 8Mbit serial Flash memory module with advanced hardware write protection mechanisms. It supports high-performance commands with a clock frequencies of up to 75MHz. Memory is divided into 16 sectors, each containing 256 pages. Flash Click communicates with the target board via an SPI interface. The board is designed to use a 3.3V power supply only. It has a green LED which indicates when the board is powered.
R145  Qty:
Est. Weight: 25g. Stock: Available in 5-10 working days [i]. mikroE Icon
-
Flash 2 click
 
mikroBUS
Flash 2 click Flash 2 click is a mikroBUS add-on board for adding more Flash Memory to your target board microcontroller. It carries Microchip's SST26VF064B flash-memory module with 64 Mbits capacity. It's a highly reliable module with a specified minimum of 100,000 read and write cycles and with over 100 years of Data Retention. For data security, the module features a One-Time Programmable (OTP) 2 KB bit secure ID and a 64 bit unique, factory pre-programmed identifier. Additional software security measures include inidividual-block write Protection with permanent lock-down capability. Flash 2 click communicates with the target MCU through the mikroBUS SPI interface (CS#, SCK, MISO, MOSI) with additional functionality provided by the #HOLD pin (in place of default mikroBUS™ RST pin). The board is designed to use a 3.3V power supply.
R170  Qty:
Est. Weight: 20g. Stock: Available in 5-10 working days [i]. mikroE Icon
-
Flash 3 click
 
mikroBUS
Flash 3 click Flash 3 click is a mikroBUS add-on board for adding more Flash Memory to your target board microcontroller. It carries an ISSI IS25LP128 IC with 128 Mbit capacity.

The high-performance Flash chip operates at 50MHz at Normal and 133MHz at Fast Read speeds.

It is specified to standard 100,000 erase/program cycles with more than 20 years of data retention. The data can be erased in sectors or blocks and programmed with 1 to 256 bytes per page.

Each chip has a 128-bit unique ID for each device.

Flash 3 communicates with the target board through the mikroBUS SPI interface with additional functionality provided by HOLD, CE and WP pins. It is designed to use a 3.3V power supply only.
R170  Qty:
Stock: 1 available immediately [i]. mikroE Icon
-
SerialFlash
 
IDC10
SerialFlash The SerialFlash Board provides additional memory space for your MCU. The M25P80 circuit provided on the board enables the MCU to use additional 8Mbit flash memory via a Serial Peripheral Interface (SPI).
R200  Qty:
Weight: 7g. Stock: Available in 5-10 working days [i]. mikroE Icon
-
Compact Flash
 
IDC10
Compact Flash The Compact Flash Board allows you to connect your development or prototype board to the Compact Flash card. You just have to establish connection between these two devices in order to enable data write or read to/from the Compact Flash card.
R300  Qty:
Weight: 15g. Stock: Available in 5-10 working days [i]. mikroE Icon
-
FRAM click
 
mikroBUS
FRAM click FRAM click brings 256Kbit (32,768 words x 8 bits) of Ferroelectric Random Access Memory to your design. It features the MB85RS256A module which uses the ferroelectric process and silicon gate CMOS technologies for forming the nonvolatile memory cells. It is able to retain data without using a back-up battery. The memory can be used for 10 bilion read/write operations and does not take long time to write data unlike Flash memories or EEPROM. It uses SPI to communicate with the target device. Maximum operating frequency is 25MHz. The board is designed to use 3.3V power supply only.
R215  Qty:
Est. Weight: 20g. Stock: 1 available immediately [i]. mikroE Icon
-
SRAM click
 
mikroBUS
SRAM click SRAM click lets you add 1Mbit of additional SRAM memory to your devices, via the 23LC1024 chip. It organizes the memory into 8-bit instruction registers and 32-byte pages. Three operating modes for reading and writing data are available: byte, page, and sequential (the last one allows read/write for the entire memory array). The clock rate for all three modes is up to 20MHz. The board communicates with the target MCU through the mikroBUS SPI interface (MISO, MOSI, SCK, CS) with additional HOLD functionality provided through the default mikroBUS RST pin. SRAM click is designed to use either a 3.3V or 5V power supply.
R215  Qty:
Est. Weight: 20g. Stock: Available in 5-10 working days [i]. mikroE Icon
-
SerialRAM Proto
 
General
SerialRAM Proto The SerialRAM PROTO Board enables you to add a 64Kbit Serial RAM device to your prototype device. A 23K640 Serial RAM device is available on-board and communicates with microcontrollers via a Serial Peripheral Interface (SPI).
R260  Qty:
Weight: 1g. Stock: Available in 5-10 working days [i]. mikroE Icon
-
SerialRAM
 
IDC10
SerialRAM The SerialRAM Board enables you to use a 64Kbit Serial SRAM device with your development board. The board features the 23K640 Serial RAM device that communicates with microcontrollers via a Serial Peripheral Interface (SPI).
R345  Qty:
Weight: 7g. Stock: 1 available immediately [i]. mikroE Icon
-
EEPROM
 
IDC10
EEPROM The EEPROM board contains the 24C08 serial EEPROM IC with 8Kbit of memory and I2C interface. It can be used with both 3.3V and 5V systems.
R115  Qty:
Weight: 7g. Stock: Available in 5-10 working days [i]. mikroE Icon
-
EEPROM click
 
mikroBUS
EEPROM click EEPROM click is an accessory board in mikroBus form factor. It features the 24C08WP highly reliable, high performance CMOS technology serial 8K EEPROM (in DIP package). It offers significant advantages in low-power and low-voltage applications. The 24C08WP EEPROM uses the I2C addressing protocol and 2-wire serial interface which includes a bidirectional serial data bus synchronized by the clock. Address selection SMD jumpers and a power LED are available on board. Another SMD jumper is available for selecting whether board will be operating on a 3.3V or 5V power supply.
R115  Qty:
Weight: 20g. Stock: 1 available immediately [i]. mikroE Icon
-
EEPROM 2 click
 
mikroBUS
EEPROM 2 click EEPROM 2 click carries ST’s M95M02-DR EEPROM chip with 256 KB of memory. The chip has byte and page write speeds equal or less than 10 ms. It's specified for more than 4 million write cycles, with more than 200 years of data retention. The memory, organized as 262144 x 8 bits, has an additional identification page, for storing sensitive application data which can be permanently locked in read-only mode. The board communicates with the target board MCU through the mikroBUS SPI interface (CS, SCK, MISO and MOSI pins). The board is designed to use either a 3.3V or a 5V power supply.
R260  Qty:
Est. Weight: 20g. Stock: 1 available immediately [i]. mikroE Icon
-
EEPROM 3 click
 
mikroBUS
EEPROM 3 click EEPROM3 click carries Atmel's AT24CM02 DIP-8 socket EEPROM chip with 256 KB of memory. The chip has byte and page write speeds equal or less than 10 ms. It's specified for a million write cycles, with 100 years of data retention. The memory, organized as 262144 x 8 bits. The board communicates with the target board MCU through the mikroBUS I2C interface (SCL, SDA pins) with speeds up to 1 MHz. An onboard jumper allows you to select the device address (two of them can be connected on the same I2C bus, for a total of 512 KB). The board is designed to use either a 3.3V or a 5V power supply.
R200  Qty:
Est. Weight: 20g. Stock: Available in 5-10 working days [i]. mikroE Icon
-