+27 (0)11 022 5323 +27 (0)81 410 5285
Basket/Checkout
R
- -
MagnifierSearch:
Search

Search for "click":
(Click here to search this entire website for "click" with Google.)

3G click
3G click 3G click is a mikroBUS add-on board with Quectel's UG95 3G UMTS/HSPA module. The board has a rich set of components to simplify development: an SMA connector, earphone/microphone jack, MicroUSB port, as well as a SIM card slot. The UG95 module specifies data rates of up to 7.2Mbps (HSPA), and 384Kbps (UMTS). The network protocol stack includes support for TCP, UDP, PPP, MMS, FTP, SMTP, SMTPS, HTTP, HTTPS, PING, and SSL. The regular version operates on European frequency bands (900/2100@UMTS, 900/1800@GSM), whilst the American version operates on American frequency bands (850/1900@UMTS). 3G click communicates with the target MCU through the mikroBUS UART interface (RX, TX), with additional functionality provided by STAT, PWRKEY, RTS, R1, and CTS pins. The board is designed to use either a 3.3V or a 5V power supply. Note: Antenna sold separately.
Regular Version    R1,350  Qty:
Price ex. VAT. Est. Weight: 25g. Stock: 1 available immediately [i]. mikroE Icon
U.S. Version     R1,350  Qty:
Price ex. VAT. Est. Weight: 25g. Stock: Available in 5-10 working days [i]. mikroE Icon
CO click
CO click CO click carries an MQ-7 sensor for Carbon monoxide. The gas sensing layer on the sensor unit is made of Tin dioxide (SnO2), which has lower conductivity in clean air. The conductivity increases as the levels of Carbon monoxide rise. The detection range of the sensor is 20ppm-2000ppm of CO. To calibrate the sensor for the environment you’ll be using it in, CO click has a small potentiometer that allows you to adjust the Load Resistance of the sensor circuit. For precise calibration the sensor needs to preheat (once powered up, it takes 48h to reach the right temperature). CO click communicates with the target board through AN (OUT) mikroBUS line. The board is designed to use a 5V power supply only.
R260  Qty:
Price ex. VAT. Est. Weight: 20g. Stock: Available in 5-10 working days [i]. mikroE Icon
FM click
FM click FM Click features the Si4703 IC, and is a complete FM radio tuner in the form of an add-on board. It supports worldwide FM band (76 - 108 MHz). The board contains two LM4864 audio amplifiers as well. The Si4703 has a nice set of features; such as automatic frequency and gain control, RDS/RBDS processor, seek tuning and volume control. FM antenna is provided through the earphones cable (recommended length between 1.1 and 1.45 m), which is plugged into on-board 3,5mm audio connector. FM Click has a simple I2C interface. All these features make this board ideal for MP3 players, portable radios, PDAs, notebook PCs, portable navigations and many more. The board is designed to use a 3.3V power supply only.
R460  Qty:
Price ex. VAT. Est. Weight: 20g. Stock: Available in 5-10 working days [i]. mikroE Icon
IR click
IR click IR Click is an add-on board in the mikroBUS form factor. It is a compact and easy solution for adding an infrared (IR) remote control module to your design. It features the TSOP38338 IR receiver module as well as a QEE113 IR emitting diode. The 38 kHz receiver carrier frequency is recommended for RCMM, NEC, RC5, RC6, r-step and XMP codes. IR Click communicates with the target microcontroller via mikroBUS UART (Tx and Rx) or AN and PWM lines. Jumpers J2 and J3 allow you to choose between the two options. An SMD jumper is used to select between 3.3V or 5V power supply (soldered in 3.3V position by default).
R150  Qty:
Price ex. VAT. Est. Weight: 20g. Stock: 1 available immediately [i]. mikroE Icon
UV click
UV click Design devices that warn you of excesive ultraviolet radiation levels with UV click. This click boards carries the ML8511 IC that is sensitive to UV-A (365-315 nm) and UV-B (315-280 nm) rays. The board can output either analog or digital signals proportional to the amount of UV exposure. To bypass the onboard MCP3201 ADC and get an analog output, solder the A/D SEL jumper in the AN position. Depending on the position of the jumper, UV click communicates with the target board either through mikroBUS SPI (CS, SCK, MISO) or AN lines; additionally, the sensor can be enabled or disabled from the MCU through the RST (EN) pin. When handling UV click, be careful not to press or rub the sensitive surface of the ML8511 sensor IC. UV click uses a 3.3V power supply only.
R380  Qty:
Price ex. VAT. Est. Weight: 20g. Stock: Available in 5-10 working days [i]. mikroE Icon
8x8 click
8x8 click 8x8 R Click is an add-on board in the mikroBUS form factor. It's a compact and easy solution for adding an 8x8 LED matrix display to your design. It features the MAX7219 8-digit LED display driver module as well as 64 LED diodes. 8x8 Click communicates with the target microcontroller via four SPI lines (DIN, DOUT, CLK and CS). The board is designed to be powered by 5V, but can also communicate with 3.3V MCUs.
Red LEDs    R240  Qty:
Price ex. VAT. Weight: 20g. Stock: 1 available immediately [i]. mikroE Icon
Green LEDs    R240  Qty:
Price ex. VAT. Weight: 20g. Stock: Available in 5-10 working days [i]. mikroE Icon
Yellow LEDs    R240  Qty:
Price ex. VAT. Weight: 20g. Stock: Available in 5-10 working days [i]. mikroE Icon
Blue LEDs    R285  Qty:
Price ex. VAT. Weight: 20g. Stock: Available in 5-10 working days [i]. mikroE Icon
ADC click
ADC click ADC Click is an accessory board in mikroBus form factor. It includes a 12-bit Analog-to-Digital Converter (ADC) MCP3204 that features 50k samples/second, 4 input channels and low-power consumption (500nA typical standby, 2uA max). Board uses industry standard SPI communication interface. It is small in size and features convenient screw terminals for easier connections. Board is set to use 3.3V power supply by default. Place PWR SEL SMD jumper to 5V position if used with 5V systems.
R380  Qty:
Price ex. VAT. Weight: 20g. Stock: 1 available immediately [i]. mikroE Icon
Bee click
Bee click The BEE Click is an accessory board in the mikroBus form factor. It features the MRF24J40MA 2.4 GHz IEEE 802.15.4 radio transceiver module. The module includes an integrated PCB antenna and matching circuitry and communicates with the microcontroller via a SPI interface. This module is an ideal solution for wireless networks, smart home automation, building automation and other electronic applications that need wireless communication. The board is designed to use a 3.3V power supply only.
R460  Qty:
Price ex. VAT. Weight: 20g. Stock: Available in 5-10 working days [i]. mikroE Icon
DAC click
DAC click The DAC Click board is an accessory board in mikroBus form factor. It includes the MCP4921 12-bit Digital-to-Analog Converter which features a SPI interface and optional dual-buffered output. The board provides high accuracy and low noise performance for industrial applications where calibration or compensation of signals, such as temperature, pressure and humidity, are required. The board is set to use the 3.3V mikroBus power supply by default, however soldering the PWR SEL SMD jumper to the 5V position will allow it to be used with 5V mikroBus systems.
R285  Qty:
Price ex. VAT. Weight: 20g. Stock: 1 available immediately [i]. mikroE Icon
ECG click
ECG click This is an ECG (or EKG) machine on a click board. It measures the electrical activity of a beating heart through electrodes taped to the skin. The board requires little setup, and the final measurement results can be displayed as an electrocardiogram using a free Windows app. With the ECG click bundle (click + cable + electrodes) you will be able to prototype your own health-tracking and fitness devices, quantified-self wearable or you can just make an LED blink in sync with your heart.
R620  Qty:
Price ex. VAT. Stock: Available in 5-10 working days [i]. mikroE Icon
Bundle (w/ Cable + Electrodes)    R1,050  Qty:
Price ex. VAT. Stock: Available in 5-10 working days [i]. mikroE Icon
Next >