+27 (0)11 022 5323 +27 (0)81 410 5285
Basket/Checkout
R
- -
MagnifierSearch:
MCP2518FD Click (CAN) (Go to Parent Category)

MCP2518FD Click (CAN)

MCP2518FD click is a complete CAN solution, which can be used as a control node in a CAN network. The Click board™ is used to provide the microcontroller (MCU) with unrestricted access to the CAN network bus. MCP2518FD click is equipped with both the control logic and the physical interface ICs. MCP2518FD click provides a reliable high-speed CAN interface to the MCU, providing multiple operating modes (CAN 2.0, CAN FD, Listen Only mode, Sleep and Low Power mode…), CAN bit stream processing (decoding and encoding of the CAN messages, error handling…), TX prioritizing, RX filtering, FIFO buffer, interrupt engine, and more.

MCP2518FD click is supported by a mikroSDK compliant library, which includes functions that simplify software development. This Click board™ comes as a fully tested product, ready to be used on a system equipped with the mikroBUS™ socket.

R400  Qty:
Price ex. VAT. Weight: 28g. Stock: Available in 5-10 working days [i]. mikroE Icon
MCP25625 click (CAN)
MCP25625 click (CAN) MCP25625 click is a mikroBUS add-on board carrying a Microchip CAN controller with an integrated transceiver. It meets the automotive requirement for high speed operation (up to 1 Mb/s).

Named after the main chip, MCP25625 click also has a RS232 port, which is a standard connector for CAN communications. Additionally, the two CAN wires (CANL and CANH) can also be connected directly through two pins on the right edge of the board.

The click communicates with the target MCU through the SPI interface - although there are additional options that take the load off the target board MCU. To that end, all 16 mikroBUS pins are connected. There's a clock output, a Request To Send, an Interrupt, standby, reset and more. MCP25625 click can work with both 3.3V or 5V logic levels.
R390  Qty:
Price ex. VAT. Est. Weight: 20g. Stock: Available in 5-10 working days [i]. mikroE Icon
MCP2542 click (CAN)
MCP2542 click (CAN) MCP2542 click is a mikroBUS add-on board with a Microchip CAN FD Transceiver with Wake-Up Pattern. The physical layer is compliant with CAN 2.0 and CAN with Flexible Data Rate (CAN FD). It is designed specifically for high-speed CAN FD applications with communication speeds of up to 8 Mbps. Longer than usual BUS lengths are supported thanks to the improved maximum propagation delay.

The board has a standard RS232 port for CAN communications.

MCP2542 click communicates with the target board MCU through mikroBUS UART interface with an additional StandBy pin (STBY, in place of default mikroBUS AN pin). Two additional pairs of pins on the right edge of the board offer separate UART connection as well as a CAN interface.

The board is designed to use either a 3.3V or 5V power supply.
R325  Qty:
Price ex. VAT. Est. Weight: 40g. Stock: 1 available immediately [i]. mikroE Icon
MCP2517FD click (CAN)
MCP2517FD click (CAN) MCP2517FD click serves as a CAN connector. It carries a DB9 9-pin connector, as well as ATA6563 high-speed CAN transceiver. The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller through SPI interface, with additional functionality provided by the following pins on the mikroBUS™ socket: AN, PWM, INT, CS, SCK, MISO, MOSI, TX and RX.
R400  Qty:
Price ex. VAT. Stock: Available in 5-10 working days [i]. mikroE Icon
ATA6563 click (CAN)
ATA6563 click (CAN) ATA6563 click carries the ATA6563 high-speed CAN transceiver. The click is designed to run on a 5V power supply. Use the VIO SEL jumper for selecting the 3.3V or 5V logic level. It communicates with the target microcontroller over UART interface, with additional functionality provided by the AN pin on the mikroBUS™ line.
R325  Qty:
Price ex. VAT. Stock: Available in 5-10 working days [i]. mikroE Icon
ATA6570 click (CAN)
ATA6570 click (CAN)

ATA6570 click is an automotive diagnostic tool that allows CAN bus interfacing, in a series of click boards™ aimed towards automotive diagnostics. The click carries the ATA6570, a high-speed CAN transceiver that interfaces a Controller Area Network (CAN) protocol controller and the physical two-wire CAN bus. This IC has some unique features that make it a perfect choice for any embedded CAN application.

It supports both CAN and CAN FD protocol types, partial networking, local and remote wake up, an SPI interface for internal registers configuration, and it features six operating modes as well as the undervoltage and overtemperature protection. The power consumption is taken to a minimum, as the ATA6570 can power down the entire system until a valid wake-up frame is received - even on a busy CAN bus. The car battery supply pin and the CAN bus pins are protected from various interferences and voltage instabilities, typically observed in automotive systems. ATA6570 click provides you with a robust and reliable CAN bus interface.

R375  Qty:
Price ex. VAT. Weight: 33g. Stock: Available in 5-10 working days [i]. mikroE Icon