Logo Tel: +27 (0)11 022 5323
Fax: +27 (0)86 672 3570
Cell: +27 (0)72 435 0005
mail@dizzy.co.za

-
Product Catalogue - 22/08/2019
-
Prices Exclude VAT
-
-
EasyInput v1.01
thumb The EasyInput board is used for providing digital logic input levels via a tri-state DIP switch. Using the board logic one (VCC) or logic zero (GND) can be easily applied to a port pin, or the pin can be left unconnected (DIP switch middle position). The board connects to development systems via the MikroElektronika-standard IDC10 connector.
R96.50
1 available immediately
-
EasyPULL
thumb The EasyPULL Board features pull-up resistors (1K or 10K). It can be used to steer an input pin to a known state if no input is present. On-board jumpers are used to set pull-up/pull-down resistor for each pin connected to a prototype device.
1K Resistors R80
1 available immediately
-
Keypad 4X4 Board
thumb The Keypad 4x4 Board features a small keypad with calculator-style arrangement of buttons and can be easily integrated into your prototype device. It is connected to your development system or prototype device via an IDC10 connector.
R145
1 available immediately
-
mikroDrive
thumb The mikroDrive board features the high-current ULN2803 darlington-transistor array IC, with the ability to drive up to 8 external loads. A jumper is provided for power-supply selection between an external power source or microcontroller VCC. The board provides an interface between low-level microcontroller logic circuitry and external power loads.
R295
1 available immediately
-
-
-
-
-
MMC/SD
thumb The MMC/SD Board is an effective and low-cost board used to connect a development system to MMC or SD cards. This board uses SPI communication for data write or read to/from MMC/SD card. It comes with many ready-to-use examples.
R325
1 available immediately
-
SerialRAM
thumb The SerialRAM Board enables you to use a 64Kbit Serial SRAM device with your development board. The board features the 23K640 Serial RAM device that communicates with microcontrollers via a Serial Peripheral Interface (SPI).
R390
1 available immediately
-
-
LCD Adapter
thumb For Alphanumeric LCD.
The LCD Adapter Board is an effective and low-cost board used to connect your development board or prototype device to an LCD. There is an IDC10 connector as well as a potentiometer for LCD contrast adjustment provided on the board.

R165
3 available immediately
-
Serial LCD/GLCD Adapter
thumb For Alphanumeric LCD / Samsung KS0108 type GLCD.
If you need more pins, GLCD or character LCD for your applications than the Serial LCD/GLCD Adapter Board is the best choice. It is connected to an LCD/GLCD via the on-board MCP23S17 serial port expander that uses SPI communication.

R230
1 available immediately
-
-
-
-
-
3.3V-5V Voltage Translator
thumb The 3.3V-5V Voltage Translator Board features the LVCC3245A voltage translators, and enables bi-directional communication between 3.3V and 5V systems. Jumpers allow you to choose the communication direction for each of the 8 lines (communication is only possible in a single direction on each line). A screw-terminal is provided for optionally providing power to the 5V system.
2 x IDC10 cables are included with the board.

R325
1 available immediately
-
5V-3.3V Voltage Translator
thumb The 5V-3.3V Voltage Translator Board features the LVCC3245A voltage translators, and enables bi-directional communication between 5V and 3.3V systems. Jumpers allow you to choose the communication direction for each of the 8 lines (communication is only possible in a single direction on each line). The board also includes a 3.3V regulator, for optionally providing power to the 3.3V system from the 5V one.
2 x IDC10 cables are included with the board.

R325
1 available immediately
-
-
EasyConnect
thumb The EasyConnect2 Board allows you to connect peripherals to your development system quickly and easily by using high-quality connectors (5mm pitch) provided on the board. This board is useful in power and high-speed signal handling applications.
R81.50
2 available immediately
-
EasyConnect2
thumb The EasyConnect2 Board allows you to connect peripherals to your development system quickly and easily by using high-quality connectors (2.54mm pitch) provided on the board. This board is useful in power and high-speed signal handling applications.
R81.50
1 available immediately
-
EasyTEST
thumb The EasyTEST Board is an ideal solution for connecting your prototype or development board to oscilloscope or other monitoring devices. This board can be connected to your development system or prototype device via an IDC10 connector.
R98
3 available immediately
-
EasyPROTO
thumb The EasyPROTO board can be used to expose a development-board's IDC10 header as solderable 2.54mm-pitch pads.
R98
3 available immediately
-
-
SmartPROTO
thumb The SmartPROTO Board offers an effective and low-cost solution for connecting your prototype device to a PCB prototype board. It is connected to a development system or prototype device via an IDC10 connector.
R80
2 available immediately
-
RFid Reader
thumb RFid Reader Board is a 125KHz RF transmitter and reciever, featuring the EM4095 controller chip. The reader has three main functions: energizing, demodulation and decoding. The reader can be connected to a microcontroller or PC for processing the data read from RFid tags. The signal is Manchester-coded. (An IDC10 cable is included with the board).
R390
1 available immediately
-